You might have bought a brand new banner signal to promote your small business or occasion and now are questioning about one of the simplest ways to put in it. Hanging a banner shouldn’t be a troublesome job. Here’s a checklist of among the widespread locations the place banners are put in and the perfect strategies and strategies for mounting or hanging them:
Flat Wall Mounting – Most banners are ordered with grommets across the perimeter which make them pretty simple to put in on flat partitions. For Drywall, you need to use push pins by way of the fabric or grommet openings, or use plastic wall anchors with screws and washers to lock by way of the grommets and into the wall. Make sure that the washer is barely bigger than the grommet opening. For a Brick or Block Wall, use a tapcon masonry screw with a washer to lock your banner (be aware that additionally, you will want a hammer drill and a masonry bit for this technique). For a Sheet Steel Wall, use sheet steel screws and washers. For a Wooden Wall use wooden screws and washers. EIFS or Artificial Stucco Surfaces, with model names equivalent to Dryvit and Masterwall, are troublesome to put in banners on for the reason that first three/four” to four” of the floor depth is usually simply polystyrene foam. Some have had success utilizing plastic EZ drywall anchors with massive threads that permit the screw and washer technique for use for brief time intervals. Any holes within the EIFS floor ought to be crammed with caulk as soon as the banner is eliminated to forestall water injury to the construction. Normally, it’s best to tie the banner up with rope within the nook grommets and to anchor it to a tough floor above and beneath the wall.
Between Pole Mounting – When mounting banners between poles it’s best to have rope or webbing with D-rings sewn into the highest and backside seams of the banner. You may then merely tie the rope across the poles or by way of massive eye screws which may be put in on the poles. D-Rings on the finish of the webbing may be connected with bungee cords strung across the poles or additionally from massive eye screws, if current. Bungee twine mounting is a good mounting approach because it permits the banner to maneuver throughout excessive winds. Mounting banners between poles with a rope connected to easy nook grommet holes is normally a recipe for failure because the grommets will have a tendency to tear free through the first sturdy wind. Bungee cords may also be connected to nook grommet holes and can reduce the prospect of the grommets ripping out.
Garden Mounting – For short-term banners mounted in grassy areas, use a technique much like the between pole mounting. Metal T fence posts may be bought at most dwelling enchancment shops, such a Lowe’s and Residence Depot, and may be put into the bottom utilizing a publish driver. Rope, bungee cords, or heavy obligation plastic wire ties can then be used with grommets to put in the banner between the posts.
Fence Mounting – Mounting banners on a series hyperlink fence is normally a straightforward job. Merely use plastic wire ties or zip ties by way of the grommets and across the hyperlinks. For a picket fence, use the identical technique as you’d for a flat picket wall.
Ceiling Mounting – One of the simplest ways to hold a banner from a ceiling above a stage, gymnasium or auditorium is to make use of pole pockets. Pole pockets are openings which might be sewn into the highest and backside seams of the banner that permit for a inflexible PVC or steel pole to be slid by way of them. Wire, cable, or ornamental rope can then be connected to the highest pole and hung from the rafters above. A pole is then inserted into the underside pocket so as to add some weight to the banner protecting it inflexible and stationary.
Flag Mounting to Poles – Pole pockets are additionally used to mount vertical banners to the perimeters of electrical poles and lightweight poles. Generally known as Boulevard Banners, these are sometimes seen adorning metropolis streets and faculty and enterprise campuses. Banner bracket kits with projecting steel or fiberglass rods are put in on the poles to permit for mounting of the banners.
Throughout The Avenue Mounting – Giant banners for parades and occasions are someday mounted throughout a complete metropolis avenue. These are normally mounted with man wire strung simply above and beneath the banner and connected to poles on either side of the road. Snap hooks are then inserted by way of the grommets and across the wires to droop the banner. Rope can then be connected to every nook grommet on the banner and pulled tight round every pole to maintain the banner in place.
Storefront Home windows – Banners which might be designed to suit between storefront window frames may be mounted to the within of the window utilizing suction cups with hooks. The hooks are merely inserted by way of the grommet holes after which the cups are caught to the home windows.
Whereas this checklist may not cowl each doable banner mounting scenario, it ought to cowl most that you just would possibly encounter. Maybe a mix of among the banner mounting strategies and strategies mentioned above would work in some situations. It is best to now know the way to dangle a banner.